How Long Should Roof Flashing Last?

Roof Flashing Installed Around Chimney

How Do You Fix Roof Flashing?

Roof flashing repair services should be your first resource when your roof flashing is damaged. Fixing your own roof flashing is inadvisable since roofs can be extremely dangerous without proper safety equipment. The steps that your roofer will use to correct your roof flashing are as follows:

  • Roughen up the area around the hole with a wire brush or sandpaper.
  • Next, the are will need to be cleaned.
  • A patch that is larger than the hole will then be cut, and then it will be affixed with roofing cement.
  • The patch will then be covered with more roofing cement.

At the end of the day, flashing that is deteriorated or rusted will need to be replaced.

How Much Does it Cost to Replace Roof Flashing?

According to the national average, the cost to replace chimney flashing vacillates between three hundred dollars and four thousand dollars. Of course, more serious flashing repairs will cost more than a minor flashing replacement, which is why the range is so vast. The final cost for roof flashing replacement will also depend on the location of the flashing, and the current condition of the flashing.

Is Flashing Required on Roof?

There are several different types of flashing. Variations include chimney flashing and step flashing. Areas of the roof that are particularly susceptible to water damage, such as around exterior walls and roof valleys, will require the extra protection that flashing can provide. Flashing is formed according to where the flashing must be applied, and the job it was developed to fulfill.

How Long Should Roof Flashing Last?

Roof flashing is expected to last fifteen to twenty years, but in some cases, depending on the quality of installation, it could last longer. In fact, if the quality of materials and installation are very high, the flashing could last as long as fifty to eighty years. That’s why it’s imperative to procure the services of a reputable roofing company.

Can I Paint Roof Flashing?

It’s important to consider the material that your flashing is composed of. Galvanized flashing is an efficient material that protects the roof from unwanted water damage. Other varieties of roof flashing are made of plastic, roofing felt, or rubber, though it is preferable for flashing to be composed of galvanized steel. While galvanized flashing can be painted, the task should only be undertaken by a professional. A qualified roofing contractor will have painting recommendations dependent upon your roofing material and color palette.

Can Roof Flashing Be Reused

When it comes to your roof flashing, it pays to completely replace it whenever it is recommended by a reputable roofer. Roof flashing may be mentioned in a roof inspection and the subsequent roofing estimate. Not all roofing estimates will include a flashing replacement, however, homeowners are advised to insist upon a new flashing replacement when there are water problems in the area. Instances that are favorable for flashing replacement include when your roof is being replaced, or when there is water damage evident in the area. The flashing, composed of thin sheets of metal, should be installed to prohibit the channeling of water into the roof structure from an angle or joint. When properly installed, flashing can last a very long time without needing to be replaced.

What is Roof Flashing Used For

It is essential for your roof to be impermeable to water for as long as possible. Flashing makes this possible. Flashing acts as a barrier or sealer in between joints in the roof. Flashing is commonly used around vents, chimneys, and skylights. These thin sheets of metal stop water before it permeates the wall of the fixture and the shingles. When flashing is properly installed, water should be funneled toward the gutters. The function of your home is important for your continued enjoyment and longevity. If you notice that one or more of your drains is clogged, drain cleaning services in Asheville, NC can alleviate the cause.

What Gauge is Roof Flashing?

The dimensions of flashing are fairly standard. For exposed face dimensions that are in the range of four to eight inches, twenty-four gauge galvanized steel is optimum. Thicker metal is usually reserved for areas that need more protection.

Roof Flashing Around Chimney

What Sealant For Roof Flashing

Polyurethane is one of the usual flashing sealants utilized for flashing installations and repairs. Polyurethane, one of the substances refined as a commercial-grade sealant, forms permanent water and weatherproof seals in all exterior gaps and joints. Different brands have different blends of sealants. Masonry caulk and roofing cement are recommended for exterior use on roofs, chimneys and more. 

Roofwise is your local skilled roofing company, providing property owners with roof flashing in Raleigh, NC. Give us a call at (919) 457-9089 to fortify your roofing system!

What is the Best Roofing Material?

Roofing Materials in the Form of Metal

What is the Most Durable Roofing Material?

If you are currently in the market for durable roofing material, you are in great company. Many homeowners recognize that selecting durable roofing material is the pathway to a long-lasting roof. Steel is considered to be one of the most durable roofing materials on the market. Roofing materials made from steel are usually coated with aluminum to act as a protective layer. In addition, steel roofing materials are usually made from recycled metal, which is a bonus for environmentally-conscious prospective buyers. 

What Roofing Material Lasts the Longest?

Fortunately, there are several different types of roofing materials that have spectacular longevity. Metal and steel roofs can last over fifty years, as can slate roofs. Tile and concrete roofs share this particular mile mark, lasting over fifty years as well. With proper roof maintenance and repairs, any of these roofing styles can last up to 100 years. This longevity is quite remarkable and should be contemplated when deciding on a new roof.

When was the last time your roof was inspected? If you live in Raleigh, NC roof inspections can help you determine the current condition of your roof, and whether you need a roof replacement. There are many different types of roofing material on the market. Reading more about these different types will help you determine the best fit for your needs. 

What is the Least Expensive Roofing Material?

The least expensive roofing material is the asphalt shingle. Asphalt shingle roofs cost around $1.00 per square foot for the shingles. This makes it entirely probable that the cost for roofing an average single-story home can be approximately $2,000. When deciding on this particular roofing style, make sure to select a reputable, insured roofing company so that your roof will be shingled properly.

Options for Roofing Material

There are many different options for roofing materials. Read through the following list to find out more about your roofing material options.

  • Solar tiles. Solar tiles represent an exciting innovation in the roofing material market. While these tiles cost more than other solar options, they can offset energy costs with solar power and integrate seamlessly into existing shingles.
  • Asphalt shingles. This roofing material is incredibly popular. Effective in all environmental conditions, asphalt shingles are affordable and come in a variety of colors.
  • Metal. Metal roofing comes in a variety of styles and can be made to replicate popular styles like slate, tile and shake. Additionally, metal roofs come with exceptional manufacturer’s warranties.
  • Stone-coated steel. This roofing material comes in interlocking panels that are made to resemble slate, clay, or shingles. These panels can resist winds of up to 120 miles per hour. They can also stand strong against uplifting, hail and freeze-thaw cycles.
  • Slate. Incredibly, slate roofs can last over one-hundred years. Slate roofing has wonderful advantages, such as a lovely appearance, and enhanced effectiveness in cold climates. Unfortunately, this roofing material is also very heavy, expensive, and breakable when stepped on.

Home Roofing Material Options

Let’s take a moment to consider some popular styles of home roofing material. Composite shingles are a popular staple in neighborhoods because they can be made to appear like slate, tile or wood shake without the installation and maintenance costs. Composite shingles are made from poly-based products that are lightweight, fade-resistant and fire safe. Clay and composite tiles are very popular in neighborhoods because they are extremely durable and can last for centuries with the proper maintenance. 

Proper maintenance should go hand in hand with proper insulation. One of the things that can help decrease your air conditioning bill is a well-insulated roof. Consider metal roofing options as well as clay and concrete tile options a part of your insulation agenda.

Residential Roofing Material Options

Updating your existing roof adds both home value and curb appeal to your home. There are a couple of considerations that you should take into account when considering your next roof purchase. These considerations include how heavy the roofing material is and whether it will require special framing. Another consideration to include is whether or not the roofing material meets the fire codes in your location. Wood shingles are prohibited in areas of the country that are prone to fires. For instance, after the Hayman Fire in 2002, Colorado Springs banned new wood roofs.

What Roofing Materials Do I Need

There are many different roofing materials that are necessary for roof installation. From the underlayment to the ridge cap, roofs need the proper methods and materials in order to function well in different kinds of weather. The tools you will need for roofing include a roofing hammer, a roofing shovel, pry bars, heavy-duty gloves, a framing square, a chaulking gun, tin snips, a hammer tacker, and more. While the list goes on, it’s important to recognize when a home improvement task extends beyond the homeowner’s skill set. While many home projects are fun to do, it’s always advisable to procure a professional for good roof work. Roofers have the insurance and safety precautions to make that their roof repairs go smoothly. 

Roofing Materials Definition

Roofing material is defined as the outermost layer on the roof of a building. Sometimes this layer is self-supporting, but generally-speaking, it is usually supported by an underlying structure. The roofing material of a building is responsible for providing shelter from inclement weather.

Roofing Materials in the Form of Concrete Tile with a Blue Sky Background

Roofing Materials and Prices

With each roofing material, there is a general corresponding price. Labor costs will differ depending on the area of the country. It is important to note that longevity does not ultimately determine the price. Clay tile usually costs $300 to $600 per square and lasts fifty to one-hundred years. Metal costs $120 to $900 and has a lifespan of 40 to seventy years. Another example is wood or cedar, which prices out at $250 to $600 and lasts up to thirty years. Whichever roofing material homeowners ultimately select for their home, should be determined based upon price, longevity, durability, climate, and design.

Get started on your service. Call our office at (919) 457-9089 to start looking at your excellent range of roofing materials in Raleigh, NC!

How Do You Care For A Flat Roof?

Flat Roof After A Commercial Roof Cleaning

What Do You Use to Clean a TPO Roof?

It needs to be said that a building owner invests time and money into their low slope roof installation. Yet it is also true that the time and money investment don’t end after the roof installation. As a matter of fact, commercial roof cleaning needs to be completed at least twice a year in order to keep the roof performing well for a long time. Your roofing contractor will use a number of tools in order to execute the cleaning process properly. These tools include utilizing a low-pressure washer with a mild cleaning detergent. It is recommended for contractors to use a soft-bristled, long-handled brush or floor broom with a cleaning solution consisting of mild, non-abrasive household detergent and water to clean the surface of the roof membrane.

How Do You Protect a Flat Roof?

The flat roof on your building not only protects the physical structure, but it also protects the investments you have made in your business. There are a number of ways for owners of flat roofs to protect these protective structures. The first step? Educate yourself about the specific roofing material you have on your roof. After all, each roof surface type and waterproofing material has its own challenges and advantages. Another step that business owners can take is to inspect their roof on a twice-yearly basis. This can assist business owners with the ability to discern upcoming roof problems and get the roofing repairs necessary.

Should I Remove Moss From My Flat Roof?

It is true that a flat roof of any kind of material can become a host to moss. While moss may seem to be relatively harmless compared to other invaders, moss can shorten the life of wood, metal, asphalt, concrete or clay roofs simply through encouraging the pooling water to stick around in the shallow root system. This aggregate effect of the water actually slowly deteriorates the surface of the roof, as water has a habit of infiltrating roofing membranes over time. In order to remove moss, use a bleach and water combination. Knock away any large clumps of moss, and to any remaining fragments, please spray or apply the water/bleach combination. The moss will turn brown in minutes, and then you can hose the area down with water and check. Please repeat until all the moss is gone.

Can You Pressure Wash A TPO Roof?

Pressure washing a TPO roof is certainly possible, but please read further in order to maximize results. Protecting the TPO roof through regular maintenance is important, but also be careful to utilize the correct methodology in order to protect the roofing membrane itself during the process. Only trained professionals should be allowed to conduct roof washing. This recommendation stems from safety and effectiveness concerns. During the roof washing process, protect any low curbs, base flashings, or other points where water could enter through the use of a pressure washer. Run-off from the cleaning solution will kill plants, so all desired plants need to be removed. Contractors typically utilize a low-pressure washer to rinse off the top layers of dust, then use a soft-bristled brush to remove any remaining detritus.

The remainder of the cleaning solution will be removed with water from the low-pressure washer. Mechanical dirt lifting abrasion is another recommended cleaning process for TPO roofs.

How Long Will a Flat Roof Last?

Generally speaking, flat roofs usually come with a ten to twenty-year warranty, but the roofs themselves can last twenty-five years or more if properly installed and maintained. After all, the lifetime of a flat roof depends on various factors. If water is left to pool on the surface of the roof for long periods of uninterrupted time, that will produce a negative impact on the life of the roof. All repairs and cleanings need to be completed in a timely fashion. Speaking of things that should last, your air conditioning unit is important. Through using routine ac maintenance you can create an environment where your air conditioning unit will last for years to come.

Flat Roof Cleaning Services

Commercial roof cleaning, with a special emphasis on commercial preventative roof maintenance, is important for creating a long-lasting roof environment. It is important to note that the roof of the building is the first defense against torrential rains, snows, wind, and hail. Add to that, the potential damage of prolonged UV rays from the sun. Given this fact, it is important to establish a healthy regimen of roof maintenance. Clean roofs maintain a lower surface temperature which not only prolongs the life of the roof, it also helps to reduce energy consumption on hot weather days. Flat roof cleaning services can be procured easily with the correct research methods.

Commercial Roof Cleaning With Vents

Roof Cleaning Is It Necessary

Roof cleaning is indeed necessary. For Raleigh, NC commercial roof cleaning is available. Roof cleaning creates an optimum environment for the roof. Roofs need to be free of moisture, and the causes that can create lingering effects, such as moss. Roof cleaning can also expose sources of roof damage, making it easier to address roof repairs in a timely manner. Do you have employees? If so, they stand to benefit from a roof cleaning, since mold and algae can grow on the surface of a roof, and eventually penetrate, sickening the employees. Protect the health of your employees and your building structure by initiating the roof cleaning process with a local roofing company.

Roof Cleaning and Painting

It is important for the roof cleaning company that an individual selects to utilize a gentle but thorough approach for your flat roof. This is because moss needs to be thoroughly removed, not blasted around the roof with a high-intensity pressure washer. An effective roof cleaning solution will eradicate all mildew, fungus, mold, and algae, including the microscopic spores that are produced by these fungi. After a proper roof cleaning, a new coat of paint may be in store. Ask your local roof cleaning services whether or not a new roof paint coating would benefit the surface of your roof.

Roof Cleaning How-To

Please consult the following list with regard to how your local roofing contractors will clean the surface of your roof.

  • Once all the leaves and debris have been brushed away, only revealing a layer of dust and dirt underneath, the contractors can then initiate the next stage of the process.
  • All flashing and sensitive plants and structures will need to be protected and covered during the process.
  • Your roofer will utilize a low-impact cleaning solution that matches the water-proofing needs of your roof, and apply it in a sensitive but thorough manner. Pressure washers may be utilized for roof cleaning, but they should be applied at a low PSI (pounds per square inch.)

Do you have a commercial roof cleaning on your business agenda? Our staff at Roofwise are ready to take your phone call at (919) 457-9089. Receive an exemplary commercial roof cleaning in Raleigh, NC with our qualified roofers.

Why Have a Green Roof?

Green roofs use natural elements for better water management and energy efficiency.

Green roof vs. traditional roof

When you hear the term “green roof” you might get several definitions, from using roof coatings to preserve a roof, which reduces the amount of roofing material being thrown away, to actual vegetation installed on a roof as a source for energy efficiency, improved air quality, and better management for water runoff.

For the most part, when talking about green roofs here, we’re thinking of roofs with vegetation grown on the top layer. While much more common in Europe, interest is increasing over green roofs in the U.S. for both residential and commercial roofs as environmentally friendly alternative to traditional roofing systems like shingles or tile.

When it comes to comparing green roofs vs. traditional roofs, green roofs offer quite a few advantages, especially if you are interested in making your home or business more environmentally friendly.

Because of their unique design, green roofs manage water runoff better than traditional roofs because the plants on a green roof will absorb the water. Green roofs also tend to be more energy efficient than traditional roofs, serving as a source of heat absorption. These roofs are also known to improve air quality both inside and outside of the home or office.

On the other hand, depending on the system, green roofs tend to cost more to install than many traditional roof systems, especially asphalt shingles. But, these initial costs are offset by long-term cost savings, not only through energy savings but for lower maintenance costs as well.

Some newer innovations in traditional roofing such as synthetic shingles offer environmentally friendly aspects, especially when it comes to longevity and the ability to recycle the material used in the roofing system.

If you are interested in green roof installation in Raleigh, NC, give Roofwise a call at (919) 457-9089. We can answer any questions you have about green roofs or schedule you for services.

Are green roofs cost effective?

Once installed, green roofs can prove very cost-effective. In fact, depending on system you install, the initial installation of a green roof is usually one of the most costly aspects of a green roof.

These initial  costs are often offset by the long-term benefits. Depending on the size of the system, green roofs are generally low maintenance. You basically have a garden on your roof, so some of your primary expenses will be the same as upkeep for a garden.

One big advantage to green roofs, according to recent studies, is that they can improve the lifespan of the roofing membrane, almost doubling it compared to a traditional roof. Green roofs protect the roofing membrane the stress caused by high temperatures and reduce daily temperature fluctuations.

Green roofs need drainage for excess water.

Do green roofs need drainage?

While much of the water from precipitation will be absorbed by the plants on a green roof, the roof still needs a drainage system to drain off the excess water. Excess water has to be drained to keep the plants from becoming waterlogged and oxygen depleted, and to protect the roof’s structure.

Do green roofs provide insulation?

Green roofs are known for their energy efficiency. While technically green roofs have little or no actual insulating effect on the roof’s R-value, or the measurement of how well a material resists the flow of heat, green roofs do effectively absorb heat, creating a buffer against temperature fluctuations. Their surface temperature usually stays the same as the outside air temperature. They also provide shading to help with cooling. It’s these aspects that make green roofs valued for their energy efficiency.

How do green roofs work?

You have two main types of green roofs, extensive and intensive. An extensive roof uses a thinner layer of soil than an intensive roof and usually houses plants like mosses, while intensive roofs allow for larger plants, including trees. These types of roofs work best for low sloped roofs. Both kinds, however, work essentially the same.

Like a regular roof, a waterproof roofing membrane is installed, and occasionally insulation is installed. A layer of soil for the plants is added over the roofing membrane and act in a similar way as shingles might for a traditional roof. The plants on a green work in part to help absorb water, although excess water will require a drainage system to drain off. The green layer also aids in heat absorption and reducing the home’s heating and cooling needs.

How are green roofs energy efficient?

As above, green roofs help maintain energy efficiency primarily through heat absorption, shading and regulating temperature fluctuations. One study indicates that even small green roofs can reduce energy demands in the summer by 75%.

Green commercial

While green roofs are built for both residential and commercial roofs, you may want to consider a green roof for your business.

Here are some reasons you might consider green commercial roofing:

  • Energy efficiency: Green roofs help reduce heat and cooling costs through heat absorption and temperature regulation.
  • Improved air quality: Dust and pollutants are removed from the air and oxygen is increased.
  • Preserves roof: The roofing membrane is protected from the heat and UV radiation and the roof’s life is extended. It’s also protected from reduced wear from drainage.
  • Visual appeal: Can provide a more positive space for employees

Green commercial building ideas

Besides green roofs, commercial building can become more eco-friendly in other ways, including going solar, one of the best sources for clean and low-cost energy. Roof coatings specifically designed to cool your roof can help reduce energy costs. You can also opt for other roofing systems that are much more environmentally friendly like synthetic shingles or even single-ply roofing like PVC membranes that are recyclable. Using recyclable materials in your building is another way to be eco-friendly.

When considering environmentally friendly building options, you may also want to look into the health and well-being of you employees. One way to do this is by installing a water softener for clearer, healthier water.

Green roof and sustainability

Besides all the benefits mentioned above, green roofs also benefit the environment, especially in dense urban areas by reducing the Urban Heat Island Effect. Urban areas tend to trap heat more than rural areas and green roofs help reduce this by absorbing the heat.

Interested in green roof installation in Raleigh, NC? See what Roofwise can do for you to make your roofing system eco-friendly. Give us a call at (919) 457-9089 .

What Does a Roof Coating Do?

A Man is Spraying a Roof Coating On a Roof.
A Roof Coating Can Extend the Life of Your Roof

If you own a commercial property, you know one of the most important parts of the building is the roof. Because a commercial building is used to manufacture products or provide accommodations for employees to work, a roofing system is vital to making that happen. Not only does a commercial roof keep buildings, products, and employees safe from inclement weather and outside elements, they are also an investment. If your roofing is looking worse for wear or you are wanting to ensure it stays in good shape, one of the best things you can do is get a roof coating. Roof coatings are roof membranes that are applied using sprays, brushes, or rollers. The purpose of a roof coating is to extend the life of your roof, have better energy savings, reduce thermal shock, and make your roof look a lot better. If you are interested in a coat for a roof, then you need to speak with commercial roofers who have the knowledge and skills to provide roof coating services.

arts of the building is the roof. Because a commercial building is used to manufacture products or provide accommodations for employees to work, a roofing system is vital to making that happen. Not only does a commercial roof keep buildings, products, and employees safe from inclement weather and outside elements, they are also an investment. If your roofing is looking worse for wear or you are wanting to ensure it stays in good shape, one of the best things you can do is get a roof coating. Roof coatings are roof membranes that are applied using sprays, brushes, or rollers. The purpose of a roof coating is to extend the life of your roof, have better energy savings, reduce thermal shock, and make your roof look a lot better. If you are interested in a coat for a roof, then you need to speak with commercial roofers who have the knowledge and skills to provide roof coating services.

What is the Best Sealant for Roofs?

Commercial property owners who are interested in roof coatings always want to know what is the best roof coat. There are a few types of roof coatings to choose from, so the best roof coating is going to depend on what you want out of a roof coating. Here are some of the most popular roof coatings to choose from

  • Acrylic Roof Coating: An acrylic roof coating is a very popular roof coating. The reason that people love acrylic roof coatings is that they are very reflective, they are easy to install, they are one of the more affordable roof coatings, and they are resistant to dirt. While these are great qualities, you should also be aware that they aren’t good when water pools on the surface of your roof and the thickness of the coating can start to fade.
  • Polyurea Roof Coating: One of the great things about this kind of roof coating is that there are two types, aromatic and aliphatic. Other great things about this particular roof coating is that is can withstand a lot of foot traffic and it is impact resistant. While its one of its benefits, it’s also a downfall–the aromatic and aliphatic have different benefits so you have to determine which benefits are more important to you.
  • Silicone Roof Coating: If your roofing system is prone to water ponding, then you can’t go wrong with a silicone roof coating. Other reasons why commercial property owners really like silicone roof coatings is because they are able to last longer than most roof coatings and don’t erode. A disadvantage to this roof is that is can become dirty easily, which can really affect the reflective coating.

What is the Best Elastomeric Roof Coating?

A Roofing Contractor Spraying a Coating On a Roof.
There Are Many Elastomeric Roof Coatings To Choose From.

Anybody that has a building can tell you that one of the things that they dread is getting roof leaks. This is because roof leaks can cause water ponding, structural damage, mold, and other issues. In order to avoid roof leaks, something that building owners are starting to do more and more is invested in roof coatings. One roof coating in particular, elastomeric, is known for being the roof coating to use if you want to prevent or fix roof leaks. There are a couple of elastomeric roof coatings to choose from which are acrylic, butyl, polyurea, and silicone. People who are interested in an elastomeric roof coating usually want to know what the best one is, but it’s going to depend on what type of roof you have. Acrylic roof coatings are great sloped roofs, butyl is best for flat or low-sloped roofs, polyurea is a nice roof coating for rubber roofs, and silicone is best used for foam roofs.

Does a Roof Coating Stop Leaks?

If you are interested in a roof coating to stop leaks, there are some details that you need to be aware of. While roof coatings can prevent leaks and fix roof leaks, if you have a minor or major roof leak, it needs to be fixed before a roof coating is applied. Pinhole leaks are leaks that roof coatings can seal up, but it is so important that you have your roof inspected for roof leaks. If a roofer finds any leaks, they will need to fix them and then apply a roof coating to your roof. Another thing that property owners want to know before getting a roof coating is a roof coating waterproof. Some roof coatings are going to be more waterproof than others, so its really going to depend on what type of roof coating you get for you commercial roof.

How Long Do Roof Coatings Last?

The average lifespan of a roof coating is going to change from coating to coating. The lifespan also depends on the type of roof coating and how it is applied. In the same vein, a lot of people who want to know about the lifespan of coatings also ask, “How much does roof coating cost?” For a professional to spray, brush, or roll on a roof coating, it will cost somewhere between $1,000 and $2,000. But its important to be aware that it depends on the size of your roof. A gallon of roof coating material will be at least $20 and a gallon can only coat a few hundred square feet.

Just like you wouldn’t get an inexperienced HVAC contractor to install a Goodman HVAC system, you wouldn’t call an inexperienced roofer for roof coatings. If you are interested in roof coatings for your Raleigh, NC property, call Roofwise at (919) 457-9089.

Tips To Get Your Roof Ready For Cold Weather

The whole purpose of a home and roof is to provide shelter. The entire point of a roof’s functioning is then depleted when it is damaged, and that is definitely most evident in cold weather when its occupants see just how unsheltered they can become when the roof is damaged. Nothing is worse than having one of the coldest winters on record, and you have a leaky roof or a drafty window allowing all that freezing air in, causing your family members exposure and illness. While you could substitute that draft with Comfort-aire systems, your roof will need to be repaired for health and safety reasons. That is why it is important to make sure your roof is stable, sturdy, and completely sealed before winter gets here. You can do that by following the cold weather tips of Roofwise in Raleigh, NC. Call us at (919) 457-9089 if you need residential roofing repair today and get your roof ready for cold weather.

red metal roof with snow

Metal Roofing Is Easier To Install in Winter Than Shingles

What is the Best Time of Year to Replace a Roof?

While the best time of year to install and replace roofs are the end of spring to the end of fall as the rainy season is over and the days are cooler with temperatures being more predictable, roofers work year round. Advantages of getting your roof repaired or replaced in the winter is that roofers will often give substantial discounts due to slower business.

All shingle roofs have to undergo thermal sealing of temperatures over 40 degrees, which is why winter can be challenging if temperatures drop below freezing. If temperatures get below 32 degrees, you cannot get shingles installed or repaired as the thermal sealing will not properly set, which often takes days to weeks to finally adhere. There must be a consistent number of days above freezing to be able to get a shingle roof repaired or installed in cold weather. Some cold weather tips would be to get your roof done in September or October where it is cool but not freezing.

Is It OK To Roof a House in Cold Weather?

While you can shingle a roof in winter, do be aware that the shingles get more brittle the colder the temperature gets. That is why you commonly see roofers installing shingle roofs in summer and spring, even though the temperatures are higher. There are negatives to getting a shingle roof installed in the summer, too. The shingles can get so hot that the nail can go right through them like butter if too much pressure is applied with the nail gun.

If you are building a completely new home and are at the stage of adding a roof, then building the wooden foundation is recommended in the winter where there is less rain to prevent future rotting or shifting, and then installing the shingles when perhaps spring has rolled around and temperatures are slightly higher. How warm does it have to be for shingles to seal? Outside temperatures need to be at least 40 degrees Farenheit for a minimum of 24 straight hours in order for shingles to be able to properly seal.

Cold Weather Tips For Home Owners

If you are unsure if your roof needs immediate repair and cannot wait until the cold weather is over, here are some things to have inspected to be sure your roof is ready for cold weather:

  • Missing shingles
  • Sagging in your roof ridge line
  • Weathered spots around antennas, mounts, or anywhere else where the shingles meet the flashing and the sealant could have rubbed off
  • Clogged gutters
  • Proper insulation in the attic

How to Patch a Roof in Cold Weather

woman shovels snow off roof

Checking Your Roof For Damaged Flashing Is A Great Cold Weather Tips To Prepare For Winter

No one wants to be stuck outside in cold temperatures having to worry about repairing or re- roofing their house. So if you are wondering ‘how long does it take to reroof a house?’ You can expect about 3 to 4 days of actual removal and installation of the roof, and an additional day or two of construction and cleanup. These cold weather tips will help you know how long it takes for shingles to seal and the temperatures they need to be at in order to properly seal, this can help you plan your roof repair appointment.

While roof repair in cold weather is trickier, it doesn’t mean that it is impossible. Just make sure that you place the shingles for installation in bundles where they won’t get bent or deformed during installation or over time. These mutations often happen around areas of the roof where there are sudden breaks in the even surface, like a peak or valley. Also, instead of using the standard 4 nails per shingle, use 6 nails during cold weather to ensure that the sealant is properly applied.

Installing metal roofing in cold weather is much easier than installing shingles, as the metal sheet panels won’t crack, bend, or break from becoming brittle due to the colder temperatures like shingles will. Metal roofing also doesn’t require any sealing time. This means that you won’t have to worry about having to worry about leaving your roof vulnerable and open for days waiting for it to properly seal like you would with a shingle roof that could possibly lead to cold weather roof leaks. So if you are needing to get roofing done in the winter, the cold weather tips that the roofers at Roofwise in Raleigh, NC can recommend is getting a metal roof installed. Call us at (919) 457-9089 if you have any additional questions.

Is Your Roof Saving You Money?

White Flat Roof

A Reflective Roof Can Help Lower Your Energy Bill.

Everyone is always looking for the best way to save money, but did you ever think that a way to do that would be on your roof? When trying to lower your energy bill on your commercial roof, you should consider where your heart and cool air is going. If you have a roof that doesn’t do a great job at sealing in or out air, that’s where it’s going. When you have a roof that is fully sealed and has the ability to reflect the sun’s UV rays, you can cool your roof down and help keep those heating and cooling prices down lower because the air that you have inside, stays inside.

Roofing That Can Help Your Energy Bill

Roof Coating – Roof coatings are made to enhance your roof, not necessarily be one itself. That means that when you have a roof coating applied, it will do something for your roof. Many of them are able to use their reflective technology to reflect the sun’s uv rays right off of it so the top does not get as hot.

Green Roof – A green roof is one of the best ways to save money and make a better environment for everyone around you. Green roofing can be one of two things: actual live plants on your roof or a roof that has been rated economical.

Spray Foam – Spray foam roofing is a great way to seal everything out and also in. That means that there are no seams for air to push through and you won’t lose any air inside your building to the outside.

Single Ply – Single ply installation can help to reflect the sun’s uv rays and help to lower your heating and cooling bills.

If you want to lower your energy bill in Raleigh, NC, call us at (919) 457-9089 for help today.

Are You Letting Heat Escape Out Of Your Roof?

Roof Damage

Maybe It’s Time For a New Roof?

Have you been checking your electric bill and it seems to be rising higher and higher? It may be that the heat in your home is going somewhere other than staying in your home, possibly through your roof. There are many ways that this can happen and we will discuss them down below, but it is something that you should pay attention to if you suspect that your losing air somewhere. Checking your roof is one thing, but you should also be sure that your HVAC system is working correctly or get a thermostat repair before you assume it is your roof with the issue.

What Can Cause An Opening In Your Roof?

Roof Damage – Roof damage can happen a bunch of different ways and you may not even know it has happened. Unless you can see out from inside or out, there may be no way that you know if water, outside air or heat, is coming into your home.

Hail – Hail can hot your roof very hard and even penetrate the material. This means that after a huge hail storm, it is probably wise to take a quick look up there and see if any damage has occured or get a roof inspection done to check out the damage to make sure that heat is leaving this way.

Storms – Storms can knock over things like trees and send branches right through your roof.

Age – An old roof can just fall apart over time and leave gaping holes or even small openings for air to come and go from.

When you need help with heat leaving through your roof in Raleigh, NC, call us at (919) 457-9089 and let the professionals at Roofwise take the best care of you.

What is an Architectural Shingle?

Architectural Shingles

Architectural Shingles Offer a Lovely Appearance of Depth, Plus Sturdy Wind Resistance.

Shingles have been a mainstay roofing material for Americans and other countries for many decades. There are many different kinds of shingles available on the market, including …

  • Traditional Asphalt
  • 3-Tab
  • Architectural
  • Impact Resistant
  • Composite
  • Synthetic
  • and More!

When homeowners need a roofing material that bridges the gap between classic asphalt and more expensive luxury shingles, architectural shingles are the ideal choice!

What is the Difference Between Regular and Architectural Shingles?

Architectural shingles are highly lauded nowadays for their superior endurance and wonderful design. Also known as “laminate shingles” this material is installed in a special layering process that features a very strong laminate coating. The result is a very sturdy roofing system that provides long term protection and security, especially against inclement weather.

Now architectural shingles are significantly thicker than traditional slim-cut shingles, which is the primary reasons why it provides such sturdy protection. Their special layering also creates a lovely three-dimensional depth on your rooftop, providing some additional curb appeal. While typical asphalt shingles may be relatively cheaper to install, many architectural shingle materials come with generous warranties (up to 50 years)!

When Should I Choose Architectural Shingles Over Other Types?

Laminate shingles are a capable luxury roofing system that doesn’t break the bank. In terms of protective capability, architectural shingles offer incredible wind resistance (up to 120 mph). Combined with the heavier weight of the material, this reduces the likelihood of curling and torn-off shingles. That means fewer visits from your friendly neighborhood roofing company, limited repair costs over the years, and lower risk of developing costly leaks.

Call for Premium Architectural Shingle Installation!

When you need professional shingle repairs or installation in Raleigh, NC, the folks at Roofwise are happy to help. Our team offers award winning installation for several types of shingle roofing, including premium GAF shingles. If you’d like to learn more about laminate shingles or any other type of premium roofing materials, feel free to contact our team at (919) 457-9089. We’d be happy to answer any questions you may have about the roofing industry or our particular business! Be sure to ask about our Houston and Raleigh asphalt roof repair too!

Before Getting a New Roof

When it is time to get a new roof, it can be overwhelming to think of the options at hand. Whether it be a commercial or residential roof, your first, or 3rd time you’ve had to get a new roof, it does not matter. There are things that you should always take into consideration to make this the easiest process possible.

What To Do

Budget – The very first thing you should do is to create a budget. This will be able to help you determine what you can and cannot afford. Once you know what you can spend, you can then choose what kind of material you want and not have to worry if it is in your price range, cause you will already know.

Material – Knowing the kind of material you like is important, but the most important part that you need to know is how long this material is going to last. You will also want to research, how the yearly maintenance is on it and if it is going to be able to withstand heavy storms and hail.

Ask – This may be the best thing you can do in regards to your roof. It is always better to just ask a professional and get their thoughts on the matter. If you tell them what you like and what your price range is, they can then guide you to make the best choice possible.

If you need a roofer or just have a question, give Roofwise a call at (919) 457-9089 and let us help you.